Alex XiongMantej Singh
Published © GPL3+

Impactful: Detecting Subconcussive Injury

Having trouble with detecting concussions? Impactful's concussion detecting device is for you!

BeginnerShowcase (no instructions)4 hours321
Impactful: Detecting Subconcussive Injury

Things used in this project

Story

Read more

Schematics

Wiring Diagram

Code

Impact.ino

Arduino
Accelerometer, Buzzer, LED Unit
/*  ********************************************* 
 *  SparkFun_ADXL345_Example
 *  Triple Axis Accelerometer Breakout - ADXL345 
 *  Hook Up Guide Example 
 *  
 *  Utilizing Sparkfun's ADXL345 Library
 *  Bildr ADXL345 source file modified to support 
 *  both I2C and SPI Communication
 *  
 *  E.Robert @ SparkFun Electronics
 *  Created: Jul 13, 2016
 *  Updated: Sep 06, 2016
 *  
 *  Development Environment Specifics:
 *  Arduino 1.6.11
 *  
 *  Hardware Specifications:
 *  SparkFun ADXL345
 *  Arduino Uno
 *  *********************************************/

#include <SparkFun_ADXL345.h>         // SparkFun ADXL345 Library

/*********** COMMUNICATION SELECTION ***********/
/*    Comment Out The One You Are Not Using    */
ADXL345 adxl = ADXL345(10);           // USE FOR SPI COMMUNICATION, ADXL345(CS_PIN);
//ADXL345 adxl = ADXL345();             // USE FOR I2C COMMUNICATION

/****************** INTERRUPT ******************/
/*      Uncomment If Attaching Interrupt       */
//int interruptPin = 2;                 // Setup pin 2 to be the interrupt pin (for most Arduino Boards)


/******************** SETUP ********************/
/*          Configure ADXL345 Settings         */
int buzzer = 3; //Define buzzerPin
int light = 2;
void setup(){
  
  Serial.begin(9600);                 // Start the serial terminal
  Serial.println("SparkFun ADXL345 Accelerometer Hook Up Guide Example");
  Serial.println();
  //pinMode(led,OUTPUT);  
  pinMode(buzzer, OUTPUT); //Set buzzerPin as output
  pinMode(light, OUTPUT);
  delay(1000); //Add a little delay
  
  adxl.powerOn();                     // Power on the ADXL345

  adxl.setRangeSetting(16);           // Give the range settings
                                      // Accepted values are 2g, 4g, 8g or 16g
                                      // Higher Values = Wider Measurement Range
                                      // Lower Values = Greater Sensitivity

  adxl.setSpiBit(0);                  // Configure the device to be in 4 wire SPI mode when set to '0' or 3 wire SPI mode when set to 1
                                      // Default: Set to 1
                                      // SPI pins on the ATMega328: 11, 12 and 13 as reference in SPI Library 
   
  adxl.setActivityXYZ(1, 0, 0);       // Set to activate movement detection in the axes "adxl.setActivityXYZ(X, Y, Z);" (1 == ON, 0 == OFF)
  adxl.setActivityThreshold(75);      // 62.5mg per increment   // Set activity   // Inactivity thresholds (0-255)
 
  adxl.setInactivityXYZ(1, 0, 0);     // Set to detect inactivity in all the axes "adxl.setInactivityXYZ(X, Y, Z);" (1 == ON, 0 == OFF)
  adxl.setInactivityThreshold(75);    // 62.5mg per increment   // Set inactivity // Inactivity thresholds (0-255)
  adxl.setTimeInactivity(10);         // How many seconds of no activity is inactive?

  adxl.setTapDetectionOnXYZ(0, 0, 1); // Detect taps in the directions turned ON "adxl.setTapDetectionOnX(X, Y, Z);" (1 == ON, 0 == OFF)
 
  // Set values for what is considered a TAP and what is a DOUBLE TAP (0-255)
  adxl.setTapThreshold(255);           // 62.5 mg per increment
  adxl.setTapDuration(15);            // 625 s per increment
  adxl.setDoubleTapLatency(255);       // 1.25 ms per increment
  adxl.setDoubleTapWindow(200);       // 1.25 ms per increment
 
  // Set values for what is considered FREE FALL (0-255)
  adxl.setFreeFallThreshold(7);       // (5 - 9) recommended - 62.5mg per increment
  adxl.setFreeFallDuration(30);       // (20 - 70) recommended - 5ms per increment
 
  // Setting all interupts to take place on INT1 pin
  //adxl.setImportantInterruptMapping(1, 1, 1, 1, 1);     // Sets "adxl.setEveryInterruptMapping(single tap, double tap, free fall, activity, inactivity);" 
                                                        // Accepts only 1 or 2 values for pins INT1 and INT2. This chooses the pin on the ADXL345 to use for Interrupts.
                                                        // This library may have a problem using INT2 pin. Default to INT1 pin.
  
  // Turn on Interrupts for each mode (1 == ON, 0 == OFF)
  adxl.InactivityINT(1);
  adxl.ActivityINT(1);
  adxl.FreeFallINT(1);
  adxl.doubleTapINT(1);
  adxl.singleTapINT(1);
  
//attachInterrupt(digitalPinToInterrupt(interruptPin), ADXL_ISR, RISING);   // Attach Interrupt

}

/****************** MAIN CODE ******************/
/*     Accelerometer Readings and Interrupt    */
void loop(){
  // Accelerometer Readings
  int x,y,z;   
  adxl.readAccel(&x, &y, &z);         // Read the accelerometer values and store them in variables declared above x,y,z

  // Output Results to Serial
  /* UNCOMMENT TO VIEW X Y Z ACCELEROMETER VALUES */  
//  Serial.print(x);
//  Serial.print(", ");
//  Serial.print(y);
//  Serial.print(", ");
//  Serial.println(z); 
//  
  ADXL_ISR();
  // You may also choose to avoid using interrupts and simply run the functions within ADXL_ISR(); 
  //  and place it within the loop instead.  
  // This may come in handy when it doesn't matter when the action occurs. 

}

/********************* ISR *********************/
/* Look for Interrupts and Triggered Action    */
void ADXL_ISR() {
  
  // getInterruptSource clears all triggered actions after returning value
  // Do not call again until you need to recheck for triggered actions
  byte interrupts = adxl.getInterruptSource();
  
  // Free Fall Detection
  if(adxl.triggered(interrupts, ADXL345_FREE_FALL)){
    Serial.println("*** FREE FALL ***");
    //add code here to do when free fall is sensed
  } 
  
  // Inactivity
  if(adxl.triggered(interrupts, ADXL345_INACTIVITY)){
    Serial.println("*** INACTIVITY ***");
     //add code here to do when inactivity is sensed
  }
  
  // Activity
  if(adxl.triggered(interrupts, ADXL345_ACTIVITY)){
    Serial.println("*** ACTIVITY ***"); 
     //add code here to do when activity is sensed
  }
  
  // Double Tap Detection
  if(adxl.triggered(interrupts, ADXL345_DOUBLE_TAP)){
    Serial.println("*** DOUBLE TAP ***");
     //add code here to do when a 2X tap is sensed
  }
  
  // Tap Detection
  if(adxl.triggered(interrupts, ADXL345_SINGLE_TAP)){
    unsigned char i,j;
    //while(1)
    //{
    for (i = 0; i <80; i++)
    {
    digitalWrite (buzzer, LOW) ; // Turn buzzer ON
    delay (1) ;// Delay 1ms
    digitalWrite (buzzer, HIGH) ;// turn buzzer OFF
    delay (1) ;// delay ms
    }
    Serial.println("*** TAP ***");
    digitalWrite(light, HIGH); 
//    delay(5000);
//    digitalWrite(led, LOW);
    //}
     //add code here to do when a tap is sensed
  } 
}

Credits

Alex Xiong

Alex Xiong

1 project • 0 followers
Mantej Singh

Mantej Singh

1 project • 0 followers

Comments