Romekmil
Published © LGPL

Small MIDI decoder on the Arduino UNO for Hauptwerk

The small MIDI decoder was constructed to support LED indicators for stops switches in software GrandOrgue or Hauptwerk (VPO).

BeginnerProtip253
Small MIDI decoder on the Arduino UNO for Hauptwerk

Things used in this project

Hardware components

Arduino UNO & Genuino UNO
Arduino UNO & Genuino UNO
×1
Board
×1
LED (generic)
LED (generic)
×18
Resistor 1k ohm
Resistor 1k ohm
×18

Software apps and online services

Arduino IDE
Arduino IDE
AvrDudess

Hand tools and fabrication machines

programmer USB Asp

Story

Read more

Schematics

Viev

Code

Kod for Small Dekoder MIDI - Arduino UNO for GrandOrgue or Hauptwerk

C/C++
// Small dekoder Midi - R. Milewski
#include <MIDI.h>   // Add Midi Library
 
//#define LED 13 
//#define LED2 12// Arduino Board LED is on Pin 13
 
//Create an instance of the library with default name, serial port and settings
MIDI_CREATE_DEFAULT_INSTANCE();
 
void setup() {

pinMode (A0, OUTPUT); // Set Arduino board analog pins to output
digitalWrite (A0, LOW);
pinMode (A1, OUTPUT);
digitalWrite (A1, LOW);
pinMode (A2, OUTPUT);
digitalWrite (A2, LOW);
pinMode (A3, OUTPUT);
digitalWrite (A3, LOW);
pinMode (A4, OUTPUT);
digitalWrite (A4, LOW);
pinMode (A5, OUTPUT);

 

  for (int a=2; a<14; a++)
{
pinMode (a, OUTPUT); // Set Arduino board digital pins to output
digitalWrite (a, LOW); // Set Arduino board digitsl pins to KIGH
    
}
 

// self-test
  for (int a=2; a<14; a++)
{
digitalWrite (a, HIGH); // Set Arduino board digital pins to HIGH
delay(250); 
digitalWrite (a, LOW); // Set Arduino board digital pins to LOW
delay(50);  
}


 
 





  MIDI.begin(MIDI_CHANNEL_OMNI); // Initialize the Midi Library.
  // OMNI sets it to listen to all channels.. MIDI.begin(2) would set it
  // to respond to notes on channel 2 only.
  MIDI.turnThruOff(); // Turn off loop Midi IN to OUT
  MIDI.setHandleNoteOn(MyHandleNoteOn); // This is important!! This command
  // tells the Midi Library which function you want to call when a NOTE ON command
  // is received. In this case it's "MyHandleNoteOn".
  MIDI.setHandleNoteOff(MyHandleNoteOff); // This command tells the Midi Library
  // to call "MyHandleNoteOff" when a NOTE OFF command is received.
}
 
void loop() { // Main loop
  MIDI.read(); // Continuously check if Midi data has been received.
}
 
// MyHandleNoteON is the function that will be called by the Midi Library
// when a MIDI NOTE ON message is received.
// It will be passed bytes for Channel, Pitch, and Velocity
void MyHandleNoteOn(byte channel, byte pitch, byte velocity) {
    switch (pitch) {
  case 54+34:
    digitalWrite (A0, HIGH);
    break;
  case 55+34:
    digitalWrite (A1, HIGH);
    break;
    case 56+34:
    digitalWrite (A2,HIGH);
    break;
    case 57+34:
    digitalWrite (A3, HIGH);
    break;
    case 58+34:
    digitalWrite (A4, HIGH);
    break;
    case 59+34:
    digitalWrite (A5, HIGH);
    break;
   
    
    
  default:
    // if nothing else matches, do the default
    // default is optional
    break;
}
   for (int a=2; a<14; a++)
{
   if (pitch == 58+a) {
digitalWrite (a, HIGH); // Set Arduino board pin 13 to output
 } 
}
  
  
    
   
}
 
// MyHandleNoteOFF is the function that will be called by the Midi Library
// when a MIDI NOTE OFF message is received.
// * A NOTE ON message with Velocity = 0 will be treated as a NOTE OFF message *
// It will be passed bytes for Channel, Pitch, and Velocity
void MyHandleNoteOff(byte channel, byte pitch, byte velocity) {
   switch (pitch) {
  case 54+34:
    digitalWrite (A0, LOW);
    break;
  case 55+34:
    digitalWrite (A1, LOW);
    break;
    case 56+34:
    digitalWrite (A2, LOW);
    break;
    case 57+34:
    digitalWrite (A3, LOW);
    break;
    case 58+34:
    digitalWrite (A4, LOW);
    break;
    case 59+34:
    digitalWrite (A5, LOW);
    break;
    
  default:
    // if nothing else matches, do the default
    // default is optional
    break;
}

   for (int a=2; a<14; a++)
{
   if (pitch == 58+a) {
digitalWrite (a, LOW); // Set Arduino board pin 13 to output
 } 
}
  
  
}

Kod for Decoder MIDI Arduino Mega for GrandOrgue or Hauptwerk

C/C++
// Kod for Decoder MIDI  Arduino Mega for GrandOrgue or Hauptwerk
#include <MIDI.h>   // Add Midi Library
 
//#define LED 13 
//#define LED2 12// Arduino Board LED is on Pin 13
 
//Create an instance of the library with default name, serial port and settings
MIDI_CREATE_DEFAULT_INSTANCE();
 
void setup() {

pinMode (A0, OUTPUT); // Set Arduino board analog pins to output
digitalWrite (A0, HIGH);
pinMode (A1, OUTPUT);
digitalWrite (A1, HIGH);
pinMode (A2, OUTPUT);
digitalWrite (A2, HIGH);
pinMode (A3, OUTPUT);
digitalWrite (A3, HIGH);
pinMode (A4, OUTPUT);
digitalWrite (A4, HIGH);
pinMode (A5, OUTPUT);
digitalWrite (A5, HIGH);
pinMode (A6, OUTPUT);
digitalWrite (A6, HIGH);
pinMode (A7, OUTPUT);
digitalWrite (A7, HIGH); 
pinMode (A8, OUTPUT);
digitalWrite (A8, HIGH);
pinMode (A9, OUTPUT);
digitalWrite (A9, HIGH);
pinMode (A10, OUTPUT);
digitalWrite (A10, HIGH);
pinMode (A11, OUTPUT);
digitalWrite (A11, HIGH);
pinMode (A12, OUTPUT);
digitalWrite (A12, HIGH);
pinMode (A13, OUTPUT);
digitalWrite (A13, HIGH);
pinMode (A14, OUTPUT);
digitalWrite (A14, HIGH);
pinMode (A15, OUTPUT);
digitalWrite (A15, HIGH);

 

  for (int a=2; a<54; a++)
{
pinMode (a, OUTPUT); // Set Arduino board digital pins to output
digitalWrite (a, HIGH); // Set Arduino board digitsl pins to KIGH
    
}
 

// self-test
  for (int a=14; a<36; a++)
{
digitalWrite (a, LOW); // Set Arduino board digital pins to HIGH
delay(250); 
digitalWrite (a, HIGH); // Set Arduino board digital pins to LOW
delay(50);  
}


 
 





  MIDI.begin(MIDI_CHANNEL_OMNI); // Initialize the Midi Library.
  // OMNI sets it to listen to all channels.. MIDI.begin(2) would set it
  // to respond to notes on channel 2 only.
  MIDI.setHandleNoteOn(MyHandleNoteOn); // This is important!! This command
  // tells the Midi Library which function you want to call when a NOTE ON command
  // is received. In this case it's "MyHandleNoteOn".
  MIDI.setHandleNoteOff(MyHandleNoteOff); // This command tells the Midi Library
  // to call "MyHandleNoteOff" when a NOTE OFF command is received.
}
 
void loop() { // Main loop
  MIDI.read(); // Continuously check if Midi data has been received.
}
 
// MyHandleNoteON is the function that will be called by the Midi Library
// when a MIDI NOTE ON message is received.
// It will be passed bytes for Channel, Pitch, and Velocity
void MyHandleNoteOn(byte channel, byte pitch, byte velocity) {
    switch (pitch) {
  case 54+34:
    digitalWrite (A0, LOW);
    break;
  case 55+34:
    digitalWrite (A1, LOW);
    break;
    case 56+34:
    digitalWrite (A2, LOW);
    break;
    case 57+34:
    digitalWrite (A3, LOW);
    break;
    case 58+34:
    digitalWrite (A4, LOW);
    break;
    case 59+34:
    digitalWrite (A5, LOW);
    break;
    case 60+34:
    digitalWrite (A6, LOW);
    break;
    case 61+34:
    digitalWrite (A7, LOW);
    break;
    case 62+34:
    digitalWrite (A8, LOW);
    break;
    case 63+34:
    digitalWrite (A9, LOW);
    break;
    case 64+34:
    digitalWrite (A10, LOW);
    break;
    case 65+34:
    digitalWrite (A11, LOW);
    break;
    case 66+34:
    digitalWrite (A12, LOW);
    break;
    case 67+34:
    digitalWrite (A13, LOW);
    break;
    case 68+34:
    digitalWrite (A14, LOW);
    break;
    case 69+34:
    digitalWrite (A15, LOW);
    break;
    
    
  default:
    // if nothing else matches, do the default
    // default is optional
    break;
}
   for (int a=2; a<54; a++)
{
   if (pitch == 34+a) {
digitalWrite (a, LOW); // Set Arduino board pin 13 to output
 } 
}
  
  
    
   
}
 
// MyHandleNoteOFF is the function that will be called by the Midi Library
// when a MIDI NOTE OFF message is received.
// * A NOTE ON message with Velocity = 0 will be treated as a NOTE OFF message *
// It will be passed bytes for Channel, Pitch, and Velocity
void MyHandleNoteOff(byte channel, byte pitch, byte velocity) {
   switch (pitch) {
  case 54+34:
    digitalWrite (A0, HIGH);
    break;
  case 55+34:
    digitalWrite (A1, HIGH);
    break;
    case 56+34:
    digitalWrite (A2, HIGH);
    break;
    case 57+34:
    digitalWrite (A3, HIGH);
    break;
    case 58+34:
    digitalWrite (A4, HIGH);
    break;
    case 59+34:
    digitalWrite (A5, HIGH);
    break;
    case 60+34:
    digitalWrite (A6, HIGH);
    break;
    case 61+34:
    digitalWrite (A7, HIGH);
    break;
    case 62+34:
    digitalWrite (A8, HIGH);
    break;
    case 63+34:
    digitalWrite (A9, HIGH);
    break;
    case 64+34:
    digitalWrite (A10, HIGH);
    break;
    case 65+34:
    digitalWrite (A11, HIGH);
    break;
    case 66+34:
    digitalWrite (A12, HIGH);
    break;
    case 67+34:
    digitalWrite (A13, HIGH);
    break;
    case 68+34:
    digitalWrite (A14, HIGH);
    break;
    case 69+34:
    digitalWrite (A15, HIGH);
    break;
    
    
  default:
    // if nothing else matches, do the default
    // default is optional
    break;
}

   for (int a=2; a<54; a++)
{
   if (pitch == 34+a) {
digitalWrite (a, HIGH); // Set Arduino board pin 13 to output
 } 
}
  
  
}

Credits

Romekmil

Romekmil

5 projects • 2 followers

Comments